Motor Guard M-26 Plasma Air Filter Kit for Miller, Thermal Dynamics, and Lincoln

4.57 / 5 stars with 7 reviews
In stock
$165.00 $145.00
+ Free Shipping! (Save $20.00)
Help eliminate Arc "sputter."
warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Motor Guard Plasma Air Filter.

If your air isn't spray paint quality, then your eating up your tips and electrodes with dirty or wet air. This filter sold with case of 4 replacement elements should save you it's cost in no time. Same Filter And Replacement Elements Sold By Miller For $230.00.

Motm-26 And Motm-723

with questions.

Plasma Cutting Systems: Compressed Air Filter
M-26

A Sub-Micronic Compressed Air Filter that effectively removes oil aerosols and condensed moisture...and will:

  • Eliminate Arc "Sputter"
  • Restore the Plasma System to Maximum Cutting Efficiency
  • Reduce Corrosive wear of the Electrode and Tip

The installation of a Motor Guard Filter on the Plasma Cutting system downstream of the air regulator will effectively remove the contamination from the compressed air line. This eliminates the "sputter" from the arc, restoring the plasma system to maximum cutting efficiency, and dramatically reducing the corrosive wear on the tip and electrode.

Designed to remove the smallest contaminant, oil-aerosol or drop of moisture to supply Clean, Dry, Oil-Free air to the point of use. Users of the filters report contaminant free air with higher flow rates and minimal pressure drops.

Compressed Air Filter - Plasma Cutting Systems
Model No. Pipe Size Max Flow
@ 80psi
Maximum
Pressure
Maximum
Temperature
Removal
Rating (Nom.)
Size Replacement
Element
M-26 1/4 Npt 2700 Scfh 125 psi 175 F .01 Micron 5" x 7" M-723
M-723
More Information
Brand Motor Guard
SKU IMOT00000001
MPN OKIM-26,M-723(CS4)
Mfgs MPN MOTM-26, MOTM-723
Prop65 Yes
Manufacturer's Warranty Yes
Skill Level Weekend Warrior, Career Welder
Process Plasma
Discontinued Product No
Outstanding 5 Best customer service I have experienced in a long time. I will be a customer many times over
Motor Guard Plasma Air Filter 5 Not at all happy with the mounting, inlet & outlet arrangement of the M-26/30. Bought a M-60 online and mounted it at the compressor, much better arrangement. Also did not receive the 50 dollars off the purchase price of the Cutmaster 58 that recently purchased.
Great deal thanks 5 Great deal thanks
My order came very well 5 My order came very well packaged and arrived faster than expected. Great company to do business with.
Huge for a portable plasma cutter filter 4 This has a great reputation. But, there's a reason there's no picture of it next to a plasma cutter. This thing is quite large. I got it for my THermal Dynamics cutmaster 42. The plasma cutter will be used under ten times a month. For the amount of use, this size seems a bit overboard. Whatever; I'd rather have an over-engineered filter than one that isn't enough for the plasma cutter.
NOT for smaller plasma cutters 3 I chose this over Miller's filter because the description said it was for portable plasma cutters. The line input and outputs do not make it good for this use. It is three times the size you think it is. The instructions tell you to also get a water separator before this. Again, the input is not set up for this very well by its location. I'm sure it works fine. I need to wait until my water separater comes in though. I'll have to run the compressor line to that, then a hose from that to this filter, then another line to the plasma cutter. It would be great for permanently mounted on the wall. Don't advertise this for a smaller portable plasma, because it is not a good match.
Perfect 5 One of the best options cost/value that I have purchased for my plasma cutter
Copyright © 2022 Weld My Ride. All Rights Reserved.